H3C S3600交换机怎么划分VLAN
- 提问者网友：树红树绿
- 2021-07-17 19:15
- 五星知识达人网友：蕴藏春秋
- 2021-07-17 20:39
基本是这样
进入配置模式
<SwitchA>sys
方法1
1．创建（进入）VLAN10，将E1/0/1加入到VLAN10
[SwitchA]vlan 10
[SwitchA-vlan10]port Ethernet 1/0/1
2．创建（进入）VLAN20，将E1/0/2加入到VLAN20
[SwitchA]vlan 20
[SwitchA-vlan20]port Ethernet 1/0/2
方法2
1．进入以太网端口E1/0/1的配置视图
[SwitchA]interface Ethernet 1/0/1
2．配置端口E1/0/1的PVID为10
[SwitchA-Ethernet1/0/1]port access vlan 10
3．进入以太网端口E1/0/1的配置视图
[SwitchA]interface Ethernet 0/2
4．配置端口E1/0/2的PVID为20
[SwitchA-Ethernet1/0/2]port access vlan 20
一下是一台我配置过的3600
#
sysname main
#
radius scheme system
#
domain system
#
local-user admin
password simple fsx522
service-type telnet
level 3
#
acl number 3002
rule 0 deny ICMP destination 192.168.12.0 0.0.0.255 icmp-type echo
rule 1 deny TCP established destination 192.168.12.0 0.0.0.255
rule 2 permit ICMP source 192.168.12.0 0.0.0.255 icmp-type echo
rule 3 permit TCP established source 192.168.12.0 0.0.0.255
#
vlan 1
#
vlan 10
#
vlan 20
#
vlan 30
#
vlan 40
#
vlan 888
#
vlan 999
#
interface Vlan-interface1
ip address 192.168.1.1 255.255.255.0
#
interface Vlan-interface10
ip address 192.168.10.254 255.255.255.0
#
interface Vlan-interface20
ip address 192.168.11.254 255.255.255.0
#
interface Vlan-interface30
ip address 192.168.12.254 255.255.255.0
#
interface Vlan-interface40
ip address 192.168.13.254 255.255.255.0
#
interface Vlan-interface888
ip address 100.100.1.1 255.255.255.0
#
interface Vlan-interface999
ip address 200.200.1.1 255.255.255.0
#
interface Aux1/0/0
#
interface Ethernet1/0/1
duplex full
speed 100
port link-type trunk
port trunk permit vlan all
#
interface Ethernet1/0/2
duplex full
speed 100
port link-type trunk
port trunk permit vlan all
#
interface Ethernet1/0/3
port access vlan 20
#
interface Ethernet1/0/4
port access vlan 20
#
interface Ethernet1/0/5
port access vlan 20
#
interface Ethernet1/0/6
port access vlan 20
#
interface Ethernet1/0/7
port access vlan 20
#
interface Ethernet1/0/8
port access vlan 30
packet-filter outbound ip-group 3002 rule 0
packet-filter outbound ip-group 3002 rule 1
packet-filter outbound ip-group 3002 rule 2
packet-filter outbound ip-group 3002 rule 3
#
interface Ethernet1/0/9
port access vlan 30
packet-filter outbound ip-group 3002 rule 0
packet-filter outbound ip-group 3002 rule 1
packet-filter outbound ip-group 3002 rule 2
packet-filter outbound ip-group 3002 rule 3
#
interface Ethernet1/0/10
port access vlan 30
packet-filter outbound ip-group 3002 rule 0
packet-filter outbound ip-group 3002 rule 1
packet-filter outbound ip-group 3002 rule 2
packet-filter outbound ip-group 3002 rule 3
#
interface Ethernet1/0/11
port access vlan 30
packet-filter outbound ip-group 3002 rule 0
packet-filter outbound ip-group 3002 rule 1
packet-filter outbound ip-group 3002 rule 2
packet-filter outbound ip-group 3002 rule 3
#
interface Ethernet1/0/12
port access vlan 30
packet-filter outbound ip-group 3002 rule 0
packet-filter outbound ip-group 3002 rule 1
packet-filter outbound ip-group 3002 rule 2
packet-filter outbound ip-group 3002 rule 3
#
interface Ethernet1/0/13
port access vlan 30
packet-filter outbound ip-group 3002 rule 0
packet-filter outbound ip-group 3002 rule 1
packet-filter outbound ip-group 3002 rule 2
packet-filter outbound ip-group 3002 rule 3
#
interface Ethernet1/0/14
port access vlan 40
#
interface Ethernet1/0/15
port access vlan 40
#
interface Ethernet1/0/16
port access vlan 40
#
interface Ethernet1/0/17
port access vlan 40
#
interface Ethernet1/0/18
port access vlan 40
#
interface Ethernet1/0/19
port access vlan 40
#
interface Ethernet1/0/20
port access vlan 10
#
interface Ethernet1/0/21
port access vlan 10
#
interface Ethernet1/0/22
port access vlan 10
#
interface Ethernet1/0/23
port access vlan 888
#
interface Ethernet1/0/24
port access vlan 999
#
interface GigabitEthernet1/1/1
#
interface GigabitEthernet1/1/2
#
interface GigabitEthernet1/1/3
port access vlan 888
#
interface GigabitEthernet1/1/4
port access vlan 999
#
undo irf-fabric authentication-mode
#
interface NULL0
#
voice vlan mac-address 0001-e300-0000 mask ffff-ff00-0000
#
ip route-static 0.0.0.0 0.0.0.0 100.100.1.2 preference 60
#
user-interface aux 0 7
user-interface vty 0 4
authentication-mode scheme
#
return
- 1楼网友：洎扰庸人
- 2021-07-17 21:56
应该和思科的没什么区别吧？你可以试试看：
Switch>enable （进入特权模式） Switch#conf terminal （进入全局配置模式） Switch(config)#vlan 10（创建VLAN 10） Switch(config-vlan)#name vlan10（命名为vlan10） Switch(config-vlan)#vlan 20（创建VLAN 20） Switch(config-vlan)#name vlan20(命名为vlan20) Switch(config-vlan)#vlan 30（....） Switch(config-vlan)#name vlan30（....） Switch(config-vlan)#exit（退出vlan配置模式） Switch(config)#int f0/1（进入f0/1口） Switch(config-if)#switchport access vlan 10（将f0/1口划分到vlan 10）
这样就划分好了。。。